DIATONE MAMBA STACK BASIC F405 MINI MK3.5 30A 5S 8BIT

DIATONESKU: JH60269

Price:
Sale price$61

Shipping calculated at checkout

Stock:
Sold out

Description

MAMBA Stack Basic F405 Mini MK3.5 30A 5S 8bit

  • Add I2C function
  • When you connect the USB, the receiver and OSD settings can be saved
  • Increase the pad area
  • LED signal selection (when Mamba Led sys avaiable)
  • BEC short circuit protection
  • TVS instant high voltage protection 30V

Update

  • F405 models support F.prot(Most)
  • Upgrade the anti-interference cable
  • Use Typec(Most)
  • The pad area of Mini flight controller (20×20) increased by 140%

Added

  • Add self-recovery insurance to the receiver's 5V power supply
  • Increase the camera VCC power supply pad
  • Standard flight controller (30.5×30.5) adds spare pad
  • Gyro uses an independent Low Dropout Regulator (Low Dropout Regulator) and reduces ripple interference

Fixed

  • Add I2C function
  • When you connect the USB, the receiver and OSD settings can be saved
  • Increase the pad area
  • LED signal selection
  • BEC short circuit protection
  • TVS instant high voltage protection 30V

Update

  • Upgrade the anti-interference cable
  • Use Typec(F405 MK3 Lite FC-Micro USB)
  • The pad area of the Mini flight controller (20×20) increased by 140%

Added

  • Add self-recovery insurance to the receiver's 5V power supply.
  • Increase the camera VCC power supply pad.
  • The standard flight controller (30.5×30.5) adds a spare pad.
  • Gyro uses an independent Low Dropout Regulator (Low Dropout Regulator) and reduces ripple interference.

Specification:

FC Specifications

MAMAB Basic F405MINI MK3.5

  • MCU: 168MHz STM32F405RGT6
  • GYRO: MPU6000
  • Barometer: Yes
  • OSD: Yes
  • Blackbox: 16M Flash Memory
  • Uarts: 5 Set
  • ESC Soft: Dshot300/600
  • Power Led: Yes
  • LED Controller: BF LED

  • RSSI: Yes
  • Buzz: Yes
  • Input: 2~6S Lipo (8.4~25.2V)
  • TVS Protection: Yes
  • BEC:3.3V 0.5A& 5V 2.5A
  • MOUNTING: 20mm, M2

ESC Specifications
  • MAMBA F30 MINI
  • INPUT VOLTAGE: 2~5S Lipo (8.4V~21V)
  • CONTINUE CURRENT: 30A×4
  • BURST CURRENT: 40A (10S)
  • BEC: No
  • Target:BLHeli_S CH40
  • SOFT: Dshot300/600
  • TVS Protection: Yes
  • MOUNTING: 20mm, M2                                                                          

Supply :
  • High-Frequency 470uF/35V ×1
  • 8pin sh1.0 ×2
  • 16AWG 60mm ×2
  • AMASS Original XT30

Important Notes: 

  • Before soldering or mounting any flight controller, connect it to your PC and verify operation
  • Incorrect soldering techniques will damage this board and void warranty. Please use the correct sized tip, temperature and technique. Temp controlled soldering irons (such as the TS100) are available for under $100 and will make soldering much easier.
  • Lifted pads are a result of incorrect soldering techniques or excess mechanical pressure and will not be covered under warranty. 
  • USB ports must be handled with care, breakage of usb ports are not covered under warranty
  • Always use a smoke stopper before powering your build for the first time.

You may also like

Recently viewed